Products & Systems

A cast iron signal housing available in three sizes and in 2, 3, and 4 aspect versions. It holds the LEDs that display red, yellow, and green signals to train drivers.

A fibre-reinforced plastic (FRP) signal housing available in three sizes and in 2, 3, and 4 aspect versions. It holds the LEDs that display red, yellow, and green signals to train drivers.

An aluminium route indicator available in six types, from 1-way to 6-way. Its LEDs light up to show the driver which track the train will take ahead.

A cast bracket that supports route indicators and shunt signals, holding them at the required offset from the signal post.

An indicator that tells the driver which platform number the train is going to enter.

An indicator that tells the driver whether the track ahead is the main line or a side (loop) line.

A cast signal that informs the driver about an immediate track change.

A miniature signal made from aluminium and cast iron that marks where automatic signalling begins and calls on the driver to proceed cautiously.

A steel signal post available in three heights: 5.6 m, 4.6 m, and 3.6 m. Signal housings are mounted on top of the post or at mid-height using offset brackets.

A mild steel ladder supplied with every post and matched to its height, allowing maintenance of the signals and installation of the equipment inside them.

A cast iron base into which a signal post is fixed for erection. The base is common to all post sizes.

A disconnecting terminal made from PBT and brass with a 25 mm centre-to-centre spacing, used inside relay rooms and location boxes.

A fuse holder made from PBT and brass. Equipment is connected through this block with fuse inserts to protect it from excess load.

A safety-critical assembly of many small parts. When operated, it relays the signal from the previous cabin that a train is approaching, after which the gateman lowers the lifting barriers.

A safety lock provided on sliding gates and location boxes.

An electrical resistance unit used in track circuits to regulate the feed current for reliable train detection.

A junction box made from castings, FRP, and SMC, installed near the track to terminate the wiring for trackside equipment such as point machines and lifting barriers.

A set of mild steel rods used to operate point machines for changing the track.

A powder-coated mild steel rack used in the relay room, on which the relays are mounted.

A powder-coated mild steel rack used in the relay room, on which terminals are mounted for wiring the various instruments installed in the room.

An 8 SWG wire used for track bonding and earthing.

A steel wire rope used in railway signalling transmission systems.

A pointed GI pipe of 50 mm diameter used to protect equipment from electrical surges.

A GI pipe used on girder bridges and track crossings; cables are protected by running them inside these pipes.

GI trunking with a base and cover that conceals cables, used on bridges.

A trackside mild steel junction box that houses equipment such as batteries, chokes, chargers, terminals, fuses, and relays.

A sign board used across track areas to inform the driver about track conditions, such as shunting limit, stop, speed limit, and block line boards.

A slotted mild steel piece used to pass a continuity wire through the track by drilling into the rail.

A mild steel flat used with earth electrodes for earthing, buried in the ground.

A mild steel slotted angle used to build racks to site requirements, for holding batteries and other equipment.

Cast iron manhole covers widely used across India and exported to countries including Belgium, the USA, the UAE, and across Africa. They are available in various sizes and weights to suit the load requirement of each road.

Cast iron hand pumps used for irrigation, widely used across the North East, Bihar, and Jharkhand for their strength and long service life.

Any component manufactured to Railway or customer drawings. Our unit can also prepare the drawing from a sample and manufacture it.

A range of small cast iron fittings used in transmission line systems.

Any component manufactured to Railway or customer drawings. Our unit can also prepare the drawing from a sample and manufacture it.

A cast iron A-type foundation used to anchor railway signalling posts and structures securely to the ground.

A cast iron B-type foundation used to anchor railway signalling posts and structures securely to the ground.

A manually operated level-crossing barrier available in three lengths: 10 m, 8 m, and 6 m.

A cast steel operating lever used in mechanical signalling systems to transmit movement for points and signals.

A complete set of transmission accessories for operating lifting barriers.

Cast iron counterweights used on overhead equipment (OHE) poles and structures.

A complete set of cast iron signalling housings, including colour light signals, shunt signals, route indicators, offset brackets, track lead junction boxes, and more.

Any item manufactured in cast iron to the customer's drawings or samples.

Any industrial item manufactured in cast iron to the customer's drawings or samples.

Cast iron pedestals used for signalling and structural mounting applications.

Cast iron hand pump body used in water hand pump assemblies.

Cast hand pump handle used in water hand pump assemblies.

Cast iron ladder base used to mount signal ladders and structures securely.

Mild steel flats used for steel fabrication and structural work.

Mild steel flat bars used for steel fabrication and structural work.

Manhole covers produced from our own in-house patterns, exported to Belgium, the USA, the UAE, and other countries, and made to any size per customer requirement.